top of page

BESS Protection and Control Architecture: Key Components, Functions and Design Considerations

Writer: VSS Power
VSS Power
1 day ago
6 min read

BESS Protection and Control Architecture

A battery energy storage system can go from normal operation to a damaging fault in just milliseconds, but protection is often left until late in many projects. The problem is that a BESS acts differently from a generator or a passive load. It has a DC source with no natural current zero [4], an inverter that limits its own fault current, and several software layers that all need to agree before anything trips. If you get the BESS protection and control architecture setup wrong, you risk nuisance trips, missed faults, or even thermal events. This guide shows how the layers work together and what you should decide early. 


What Is BESS Protection and Control Architecture? 


BESS protection and control architecture is the coordinated set of hardware protection, embedded controls and supervisory software that keeps a storage plant safe, compliant, and dispatchable. It works in three tiers: 

  • Protection: fuses, DC breakers, contactors and AC relays that clear faults. 

  • Control: the BMS (battery management system), Power Conversion System firmware and plant controller. 

  • Supervision: the Energy Management System, SCADA, and communications. 


The guiding principle is simple. The fastest layer must be hardware, and slower software layers must never be relied on to do their job. 


Key Components and Their Functions 


Battery Management System (BMS) 

The Battery Management System (BMS) monitors cell voltage, temperature and current, enforces operating limits and tells the PCS how much power the batteries can accept or deliver. Its response time is typically tens to hundreds of milliseconds, which is too slow to limit the first surge of a short circuit [4]. Treat it as a complement to fuses and breakers, not a replacement. 


Power Conversion System (PCS) 

The Power Conversion System (PCS) is the device that converts DC to AC and back again. Under IEC 60909-0:2016, the PCS is modelled as a current-regulated source, so its fault current remains close to its rated value rather than rising several times rated as would be the case with a synchronous machine [2]. Relays that are tuned to a generator-fed network can therefore be prone to under-reach. Ride-through is also important in that the PCS and BMS both require a very fast current limit path which is separate from the slower power limit updates. 


BESS Protection and Control Architecture

Energy Management System (EMS) and Plant Controller 

The Energy Management System (EMS) deals with dispatch, mode changes and grid operator set points (via the plant controller, which will command all of the inverters as a group). It's a control function, not a protection function, and it must be fail-safe in the event of a loss of communication. 

DC and AC Protection Devices 

Fuses at rack level and in the DC combiner must comply with IEC 60269-7 (fuses for battery protection) [3]. Short-circuit-only fuses will require additional overload protection, typically from the BMS [3]. On the AC side, the relays at the MV point of connection will clear grid faults. 

Protection Layers at a Glance 

Layer 

Typical response 

Main role 

Design watch-point 

Rack fuse / DC breaker 

Milliseconds 

Clears DC short circuits 

Check DC breaking capacity at system voltage 

PCS internal protection 

Cycle level 

Current limiting, DC-link protection 

Align with grid-code ride-through 

BMS 

Tens to hundreds of ms 

Limits, contactor opening 

Not a substitute for fuses 

AC protection relay 

Tens of ms 

Clears grid-side faults 

Low fault current can cause under-reach 

EMS / plant controller 

Seconds 

Dispatch and curtailment 

Fail-safe on comms loss 

Design Considerations That Decide Project Success 


1. Study Both Sides of the PCS 

A BESS system requires two fault studies. IEC 61660 applies to the DC side (where current has no zero-crossing) and deals with thermal and mechanical stress on the busbars [1]. IEC 60909 covers the AC side [2]. Omitting either one creates a gap which invariably turns up during commissioning. 


2. Choose the Earthing Philosophy Early 

Solidly earthed, ungrounded with insulation monitoring, and high-resistance-earthed DC buses all suit different PCS topologies [5]. That's a design decision, not an afterthought and should be in line with the IEC 60364 and BS 7671 requirements. 


3. Design Communications and Cybersecurity Together 

IEC 61850 GOOSE carries the fast trip and interlock signals; MMS carries the supervisory data [6]. Protection commands are now being transmitted as network packets, which means that IEC 62351 deals with message security, and IEC 62443 provide the wider industrial cybersecurity framework [6]. Protection traffic is to be kept separate from EMS and remote access traffic. 


4. Align With Fire Safety and Grid Rules 

IEC 62933-5-2 (2nd edition published December 2025) covers safety for grid-integrated electrochemical storage [7]. This has been supplemented by widespread reference to IEC 62619, UL 9540A, and NFPA 855. In the UK, NFCC have updated its grid-scale BESS guidance [8]. PAS 63100:2024 is only for domestic systems [8]. NFCC is keen for developers to contact the local fire and rescue service at an early stage [8]. Grid connection in the UK is via G99; Middle East and Indian projects are governed by the relevant utility codes and CEA. 


Where the Industry Is Heading 


Grid-forming inverters now give storage a role in supplying fault current and system strength. Digital substations using IEC 61850 process buses reduce copper cabling and speed up engineering [6]. The same architecture applies to a solar energy storage system, where DC coupling adds another fault path to study. 


Common Mistakes to Avoid 


Three issues keep coming up on projects. The first is relying on the BMS to clear short circuits, which only the hardware can interrupt in time. The second is to apply the generator-based relay setting philosophy to an inverter-fed network. The third is to treat communications as an afterthought, so that one misconfigured GOOSE subscription or one open remote access path will defeat a perfectly good design. 


Practical Checklist for Engineers 


  • Run fault studies on both the DC and AC sides. 

  • Specify battery-duty fuses and confirm DC breaking capacity. 

  • Give the BMS and PCS a fast current limit path. 

  • Document the earthing method and the insulation monitoring. 

  • Test the GOOSE trips and interlocks and define the cyber zones. 

  • Confirm fail-safe behaviour on EMS comm loss. 

  • Open early discussions with the fire service and the network operator. 


Protection Response Ladder

Conclusion 


Strong BESS protection and control architecture with fast hardware protection under intelligent control and then secure supervision. Get the fault studies, earthing, comms and fire safety all sorted out prior to procurement, not after. 

VSS Power supports clients with Electrical and Power Engineering and Substation Design Engineering in the UK and beyond. To discuss your storage project, contact VSS Power at vsspower.com. 

 

Key Takeaways 


  1. Hardware clears the faults first. The fuses and DC breakers operate in milliseconds; the BMS operates in tens to hundreds of milliseconds. 

  2. PCS fault current is controlled. Inverter-fed networks can result in relay under-reach if generator-style settings are simply carried over. 

  3. Look at both the DC and AC sides. IEC 61660 and IEC 60909 cover different parts of the same system. 

  4. Communications are part of the protection. IEC 61850 GOOSE trips require IEC 62351 and IEC 62443 thinking from day one. 

  5. Engage the regulators and the fire services right from the start. The UK guidance is in the process of change, and IEC 62933-5-2 was re-issued in December 2025. 


FAQs 


1. What is BESS protection and control architecture?  

It is the combination of hardware protection devices, embedded controls (BMS and PCS) and supervisory software (EMS and SCADA) that keeps a battery energy storage system safe, compliant and dispatchable. 


2. What is the difference between BMS, PCS and EMS in a BESS?  

The BMS protects and monitors the batteries, the PCS converts power between DC and AC, and the EMS decides when and how much the system charges or discharges. 


3. Can the BMS replace fuses and DC breakers?  

No. The BMS response time is normally too slow to prevent short-circuit current; therefore, it works alongside hardware protection rather than replacing it. 


4. Which standards apply to BESS protection design?  

Commonly referenced standards include IEC 62933-5-2, IEC 62619, IEC 60269-7, IEC 60909, IEC 61660, IEC 61850, IEC 62443, UL 9540A and NFPA 855, plus local grid codes such as G99 in the UK. 


5. Why is fault current from a BESS different from a generator?  

A PCS is a current-regulated power-electronic source, so it limits fault current close to its rated output, which can make fault detection harder for conventional relay settings. 


Reference 

  1. IEC 61660 DC short-circuit currents in BESS:  https://sunlithenergy.com/?p=6526 

  2. IEC 60909 AC short-circuit currents and PCS behaviour: https://sunlithenergy.com/?p=6558 

  3. BESS overcurrent protection and IEC 60269-7 fuses: https://www.nacleanenergy.com/energy-storage/how-to-properly-protect-a-bess-power-circuit-from-overcurrents 

  4. DC short-circuit behaviour and BMS response times:  https://www.hiitio.com/?p=104024 

  5. BESS earthing design guide:  https://sunlithenergy.com/?p=6164 

  6. IEC 61850 in the digital substation (GOOSE, MMS, IEC 62351, IEC 62443): https://www.innobu.com/en/articles/iec-61850-digital-substation-protection-control-2026.html 

  7. IEC 62933-5-2:2025 (2nd edition) preview:  https://www.en-standard.eu/publicdoc/iec_previews/4003707.pdf 

  8. NFCC grid-scale BESS guidance and PAS 63100 scope:  https://nfcc.org.uk/our-services/building-safety/grid-scale-energy-storage-system-planning-guidance-for-fire-and-rescue-services/ 

 

Comments


bottom of page